Microscan MS-4 Manual do Utilizador descarregar pdf

Step 2 — Connect the System

Connecting by RS-232 / RS-422

• Connect the Imager (1) to the IB-3PC interface (2).

• Connect the comm. cable (

) to the host (

) and to the host connector on

the IB-3PC (

• Connect power supply (3) to the IB-3PC (2).

• Apply power to the Imager.

Connecting by USB

• Plug the MS-4 Imager’s USB cable into a host USB port.

• Apply power to the Imager.

Hardware Configuration

Caution:

Be sure that all cables are connected

BEFORE

applying power

to the system. Always power down

BEFORE

disconnecting any cables.

Step 1 — Check Hardware

Item Description Part Number

MS-4 Imager FIS-0004-XXXXG

IB-3PC Interface Box FIS-0001-0030

Power Supply

97-100002-04 (110V)

97-100002-05 (220V)

Comm. Cable 61-000010-01

Hardware Required

Quick Start Guide

MS-4 Imager

P/N 83-200004-04 Rev A

Step 3 — Position Imager

•

Position the Imager at a distance from the symbol that matches the factory

pre-set focal distance. For example, if your Imager is pre-set at 4”, position

the parting line 4” from the symbol.

• Tip the Imager relative to the symbol to avoid the glare of direct (specular)

reflection. The case parting line should be perpendicular to the plane of the

symbol by either pitching the symbol or the Imager as shown.

• Position the Imager in a place with as little ambient light as possible.

• Symbols can be rotated (tilted) at any angle; however, for best results

symbols should be aligned with the FOV (field of view).

• In the case of linear symbols, aligning the bars in the direction of their

movement (“ladder” orientation) will minimize the chances of blurring,

and will produce better reads.

• Avoid excessive skew or pitch. Maximum skew is

±30°

; maximum pitch is

±30°

Note: For instant setup and validation, the MS-4 can be hand-held or

placed on its side. For accuracy, however, Microscan’s mounting arm

adapter kits (P/N 98-000048-01 or -02) are recommended.

Imager / Symbol Positioning

±30°

Step 4 — Install ESP

ESP Software can be found on the Microscan Tools Drive that is packaged

with the MS-4 Imager.

1. Follow the prompts to install ESP from the Tools Drive.

2. Click on the ESP icon to run the program.

Note: ESP can also be installed from the Download Center at

www.microscan.com.

Minimum System Requirements

• 233 MHz Pentium PC

• Windows 8, 7, Vista, or XP operating system

(32-bit or 64-bit)

• Internet Explorer 6.0 or higher

• 128 MB RAM or greater

• 160 MB free disk space

• 800 x 600 256 color display (1024 x 768 32-bit color recommended)

Refer to the MS-4 Imager User Manual for detailed information about using

ESP to configure the MS-4.

Step 5 — Select Model

When you start ESP, this menu will appear:

• Select the MS-4 from the menu and click OK. If you do not want to make

this selection every time you start ESP, uncheck “Show This Window at

Startup”.

• Click Yes when this dialog appears:

Note: If you need to select

another reader model later,

click the Switch Model button

near the top of the screen.

1 2

MS-4 Imager 1

Resumo do Conteúdo

Página 1 - MS-4 Imager

Página 2

Mais documentos para Leitores de códigos de barras Microscan MS-4

Para ver o documento Microscan MS-4 Especificações

Microscan MS-4 Especificações (202 páginas)

Para ver o documento Microscan MS-4 Manual do Utilizador

Microscan MS-4 Manual do Utilizador (390 páginas)

Para ver o documento Microscan MS-4 Guia do Utilizador

Microscan MS-4 Guia do Utilizador (43 páginas)

Comentários a estes Manuais

Sem comentários

Microscan MS-4 Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Leitores de códigos de barras Microscan MS-4. Microscan MS-4 User manual Manual do Utilizador

Resumo do Conteúdo

Mais documentos para Leitores de códigos de barras Microscan MS-4

Comentários a estes Manuais

Manuais e produtos relacionados com Leitores de códigos de barras Microscan MS-4