Microscan QX Hawk Manual do Utilizador descarregar pdf (Página 2)

QX-1 Interface Device

+10-28V

Trigger

Ground

Trigger/New Master /

Input 1 Common

QX-1 Trigger Connector

4-pin Socket

Connector T on the QX-1 Interface Device is the trigger connector.

Connectors 1 and 3 are 12-pin plugs, and Connector 2 is a 12-pin socket. All three connectors can be

assigned to bus power and data as required by the application.

The two switches at the center of the device allow the user to route signals as needed.

This simple diagram (shown on the

base of the QX-1) illustrates how

power, communications, I/O, and

trigger signal can be routed through

the QX-1 device depending on the

needs of the application. The

switches greatly increase signal

routing flexibility.

QX-1 Communications -

I/O - Power - Trigger

QX-1 Interface Device

Power Requirements and Pin Assignments

Connector A

on the back of

the camera is

a serial M12

12-pin plug.

Ground

Output 3

Output 1

Output 2

Input 1

Default

Power

Input Common

Output Common

Host RxD

Trigger

Host

TxD

A (Serial) M12 12-pin Plug

TX (+)

RX (–)

RX (+)

TX (–)

Terminated

B (Ethernet) M12 8-pin Socket

Ter mi nat ed

CCD Power Requirements (Standard): 5-28VDC, 200mV p-p max ripple, 170mA at 24VDC (typ.), 15.5 watts (max.)

CMOS Power Requirements (Standard): 5-28VDC, 200mV p-p max ripple, 135mA at 24VDC (typ.), 13 watts (max.)

CCD Power Requirements (C-Mount): 5-28VDC, 200mV p-p max ripple, 130mA at 24VDC (typ.), 15.5 watts (max.)

CMOS Power Requirements (C-Mount): 5-28VDC, 200mV p-p max ripple, 105mA at 24VDC (typ.), 13 watts (max.)

Connector B

on the back of

the camera is

an Ethernet

M12 8-pin

socket.

Step 12 — Run the Job

When all job parameters are set, click on the

Run

step at the top of the interface. The software will download the

vision job just created to the camera and will begin the inspection

. Inspection results and the list of active tools

are shown at the right of the image view. That information can also be moved below the image area by

clicking the orientation buttons above the inspection results area.

Test Jobs

Note: For descriptions of more advanced functionality, such as setting Inspection Outputs or using the

Locate Tool and Decode Tool’s Dynamic Locate functionality to track multiple tools from image to image,

see the help documentation in AutoVISION software.



Decode Tool, OCR Tool, Match Strings Tool,

String Format Tool

Measure Tool,

Count Tool

LOT 123456

DATE 05/2012

VISION

SIMPLIFIED

Measure:

Measure the distance between

the jaws of the caliper gauges at left.

Count:

Count the circles on the dice shown

at right.

Step 9 — Set Camera Parameters

1. Click on the Camera box to the left of the image area.

2. In the camera parameters below the image area, select the desired type of Trigger, Trigger Polarity,

Photometry (Exposure and Gain), Focus, and Lighting.

Step 10 — Add Tools to the Job

1. Click on the Decode Tool or drag it onto the image area.

2. Use the anchor points at the corners of the region of interest to form a box around the Data Matrix

symbol. Leave plenty of space on each side of the symbol.

3. Now add a second Decode Tool and do the same for the 1D symbol below the Data Matrix symbol.

4. Finally, add an OCR Tool and drag the region of interest around the area of the image where “123456”

is printed.

Step 11 — Try Out the Job

Once you have configured the tools as desired, use the arrow icons in the Job area to try the job you have

just created.

Note: Most jobs will inspect multiple captured images. If only one image is being inspected, the effect of the

arrow icons will not be evident.

Try Out Job

Once

Try Out Job

in Loop

Vision HAWK Accessories

Vision HAWK Part Numbers

AutoVISION to Visionscape Upgrade 98-000217-01

Adapter Plate Kit 98-000143-01

Right Angle Mirror Kit 98-000144-01

Window Replacement 98-000146-01

15° Lens Kit 98-000147-01

30° Lens Kit 98-000147-02

45° Lens Kit 98-000147-03

L-Bracket Kit 98-000148-01

Infrared (IR) Filter 98-000205-01

Glass Window Kit 98-000206-01

L-Bracket Kit, QX Series 98-000148-01

Demo Kit, Vision HAWK 98-000215-01

Microscan Tools Drive 37-000010-01

Note: Additional accessories are available in the Microscan Product Pricing Catalog. See the Vision

Hawk Smart Camera Guide for Vision Hawk C-Mount accessories.

Vision HAWK part numbers follow the format GMV-6800-CLSYG:

Comm = 1 for Ethernet;

Lens = 0 for C-Mount, 1 for 15°, 2 for 30°, 3 for 45°;

Sensor = 0 for CCD, 1 for CMOS;

Y (Options) = 0 for AutoVISION, 2 for AutoVISION + Visionscape License

G = RoHS-Compliant

1 2

Comentários a estes Manuais

Sem comentários

Microscan QX Hawk Manual do Utilizador Página 2

Comentários a estes Manuais

Manuais e produtos relacionados com Leitores de códigos de barras Microscan QX Hawk